How To Use An Aircast Cryo Cuff

Aircast cryo-cuff has a simple design which makes it easy to use. It comprises different components that work together to provide compression and cold therapy for post-surgery recovery.

But cold therapy is a practice that has been used in more ways than one. It is not only useful for post-surgery recovery but can be useful after a hard workout, after an injury, or when you are sore.

People tend to purchase the item in specialty places both offline and online stores.

Here is what you must know about the Aircast cryo-cuff and the various aspects of this treatment. You can see more here to have more details about Aircast cryo-cuff.

What Are The Components of the Aircast Cryo Cuff

The components of aircraft cryo cuffs are present below.

 

• The cooler
• Insulation disk
• The tube
• The cryo cuff

These are the various components of the Aircast Cryo Cuff that adds value to those who want to use it for their various purposes. Remember that you can ensure to purchase it from stores like Source Cold Therapy that specialize in the right equipment for all types of people.

Now that we know about the components of this wonderful piece of equipment, here is how one would use the device.

The Steps to Use An Aircast Cryo Cuff

Here are the steps to take in using an Aircast cryo cuff in the right way.

 

Step 1: Fill the cooler

To prepare the cooler ready for use, fix the tube properly to the cooler. Remember to ensure to use the tube that came with the aircast cryo cuff.

After connecting the tube to the cooler, pour cold water into the cooler up to the water line specified in the cooler. Also, pour the right amount of ice depending on how long the treatment will take. You can even fill the cooler with ice if the cold therapy takes 4-6 hours.

Finally, place the insulation disk on the ice to maintain the heat flow. After that, cover the cooler with the top until you are sure it is properly closed.

Step 2: Apply the cryo cuff

Only use an aircast cryo cuff for an aircast gravity unit. That said, you can only use an aircast knee cuff, shoulder cuff, or any of the aircast cuffs with the aircast gravity unit.

If you are using the knee cuff, first set your knee in a relaxed position, then lay the cuff on your knee. Make sure that the cuff opening is in line with your knee cap.

Strap the cuff to your knee firmly using the lower and upper straps. Make sure it is not too tight to avoid any form of discomfort.

For information on how to wear a cuff correctly, please read the user manuals of whichever cuff you want to use.

Step 3: Fill the cuff

To fill the cryo cuff with cold water, connect the tube with the cuff by pushing it in slightly streaming. Apply a little pressure until you hear a click sound.

Next, open the air vent on the top of the cooler and raise the tank a little above the cuff to allow water to move down easily. After filling the cuff, close the vent and place the cooler on a surface.

Step 4: Disconnect the cuff from the tube

After filling the cuff with cold water, disconnect the cuff from the tube by pressing the button around the cuff where the tube is connected. Then the tube can be removed easily.

 

Use the cuff for 20-30 minutes, then change the water in the cuff.

 

Step 5: Change the water

To change the water in the cuff, attach the cuff to the tank. After you have fixed the cuff and the tube together, the next thing to do is to open the vent at the top of the cooler then place the cooler lower than the cuff. This action will allow the water to flow out of the cuff into the tank. Then, fill up the cuff using step 3.

 

To continue using the aircast cryo cuff for a long time, repeat the processes over and over again. You can walk around with the cuff and even exercise with the cuff on.

A Simple Note

It is important to know that this type of therapy might not be advisable for people with Raynaud and persons with cold hypersensitivity. The application and equipment is very useful to many individuals but it is essential to make sure that you follow the right steps.