What is a Split System Air Conditioner and How Do I Install One?

A split system air conditioner is a piece of electrical equipment that helps manage air warmth inside your house. These conditioning units are also primarily quiet and easy to install, making it possible for the general public to own them. These ACs do not have ducts, so you have to install a cooling unit inside your house and a condenser outside. You can then run the piping and power cable in between units. Suppose you do not want to call a professional to install your split system air conditioner. In that case, you need to possess some experience with plumbing and electricity works. If you don’t have any experience then you can contact one of the Best Air Conditioning Installation experts in Mission Viejo they will do the job correctly. Each unit is unique in its regard, and the manufacturers include their special features inside the machine. The general installation, however, remains the same for every device.

Set up the indoor conditioning unit.

1. Select a location that does not have any obstructions beneath it to mount your indoor unit. You might have to form a hole through the walls to connect pipes from the interior unit to the exterior unit. So you should always make sure to choose a location that enables the connection. The spot should also be away from direct sunlight and heat to provide the best result. You can mount the conditioning unit at least seven feet above the floor to ensure there is at least 6-12 inches of open area on both sides of the unit for the best airflow. You can also find information about correct locations if you check this link here right now. 
2. Secure the plate for mounting your machine on the interior wall. You can hold the plate on the wall at a secure position and screw it to the wall. You can use a handy pencil to mark the holes for your screw and then drill them to make it easy for the screw to go in. You can position the plate first to see if it matches the holes and then put in the plastic anchors to secure the plate on the place using tapping screws. 
3. Make a three-inch diameter hole in the wall to feed the pipes outside the room. You can mark a hole form on the plate and use a saw or drill with a hole attachment to make a circular three-inch opening through the wall, slightly downward towards the ground, to make sure drainage remains adequate. It would help if you always made sure there are no wires and pipes inside behind the wall before cutting the hole. If you lack the necessary equipment, Get information Here if you Looking for Air Conditioning Installation, Mission Viejo. 
4. Properly check the electrical connections in the indoor unit. 
5. You can lift the AC’s front panel and remove the cover to find a collection of cables. You have to make sure the cable wires are connected with the screw terminals and match the diagram that the device came with. 
6. Now, you need to run the pipes from the indoor unit to the outdoors using the hole you punched the walls. You have to properly secure the pipes, cables, and drainage together with electrical tape. Now place the drainpipe near the bottom to assure a free flow of water through the system. You can then run the pipe and cable through the wall and secure them to the necessary spots on the unit, as the user manual describes. Each line in the device will have insulation already, so you will not have to worry about adding extra insulation to the system. 

Installing the condenser outdoors

1. You should always place your condenser away from any heavily wooded, dirty, dusty, or hot areas. You can find the hole you drilled through using the plate for the interior unit and position the condenser at least fifty feet away so that it is easy to attach the piping and cable. You can choose a location within at least fifteen feet from the wall to ensure the wires and pipes can connect easily. You can select an area of about twelve inches of space in the parameters to ensure the system functions well. 
2. You can put down a concrete pad on the ground in your preferred location to hold the condenser. The unit is heavy and can put a significant amount of weight if you place it on rocks and dirt. A concrete slab will provide level ground to secure the condenser in place without any issues. 
3. Now, it is time to secure the exterior unit on top of the pad. You can get yourself some rubber cushions to go with the screws and bolts, as it will help you minimize the vibration from the pad. 
4. You have to check the wiring in the exterior unit and remove the condenser cover. You can refer to the unit’s user manual to find the right combination of wires in the right spots. You can fasten the cable with clamps and replace the cover. If you cannot figure the cables out, you can contact an expert to solve this problem. Please click this site and get the best air conditioning installation service in San Diego. Our technicians can troubleshoot and repair all issues that day.
5. Your indoor unit pipes will have flare nuts that will go to the side of your external condensers. You can look around the unit to find where the pipe entrance lies on the condenser. You can connect the power cable from the indoor unit directly to the outdoor unit as well. Sometimes it is difficult to do it by yourself. 

Final steps

1. Bleed some air and humidity into the refrigeration circuit by removing caps from the two and three-way valves. You can find the slots near the service port, and you will have to connect a vacuum pump to the port. Turn the pump on till it gets to 10 mm Hg. 
2. Connect pipes with clamps to fix them on the wall. This step is necessary to ensure the cables do not move with the wind and do not water into them. If there are any significant holes in the wall, seal them with polyurethane foam. 
3. Now, you can finally test the unit by turning on the power and checking for temperatures. In case of problems, you can Get information Here if you Looking for Air Conditioning Installation, Mission Viejo.